چکیده:
زمین لرزه ی سنگچال در 11 تیر 1336 در محدوده بخش مرکزی گسل شمال البرز رخداده است. گسل شمال البرز، گسلی کمانی شکل بوده که از لاهیجان تا گنبدکاووس کشیده شده است. این گسل به همراه گسل های خزر، لله بند، کندوان و مشا در کوتاه شدگی و برخاستگی رشته کوه های البرز اثر گذار بوده اند. این کوتاه شدگی و بالاآمدگی با رخدادهای زمین لرزه ای بزرگی همراه بوده که امروزه نیز ادامه دارد. با آگاهی از هندسه گسل ها و چگونگی جابجایی گسل ها و استفاده از روش های محاسباتی تحلیل گسل ها و هم چنین با کمک حل ساز وکار ژرفی گسلش، جهت یابی بیشینه تنش حاکم بر بخشی از گسل شمال البرز که محدوده رخداد زمین لرزه بزرگ 1336 سنگچال بوده، تعیین شده است. این دو روش نتایج مشابه قابل قبولی را نشان می دهند. علاوه بر این، مقایسه یافته ها با نتایج بررسی های زمین سنجی کلی گستره، صحت و دقت یافته ها، تأیید شده است. نتایج بررسی نشان می دهد در طول گسله شمال البرز، تنش فشاری با روند شمال خاور- جنوب باختر غالب بوده که بردار امتداد لغز چپگرد نیز در آن دیده می شود. از بخش های مرکزی البرز به سوی خاور، بدلیل کاهش زاویه بین بردار بیشینه تنش و روند گسل، جابجایی حاصل از بردار چپگرد از مرکز به سمت خاور افزایش یافته و باعث بزرگتر شدن بردار برش نسبت به فشارش در بخشهای خاوری البرز می گردد. این مکانیسم، باعث رخداد زمین لرزه های فشاری در البرز مرکزی و زمین لرزه های فشاری- برشی در بخشهای خاوری گردیده که نشان می دهد بزرگای زمین لرزه های احتمالی آتی در بخش های خاوری کمی کوچکتر از زمین لرزه های البرز مرکزی باشد.
The Sangchal earthquake occurred on July 2, 1957, in the central part of the North Alborz fault zone. The North Alborz fault is an arched shape fault that continued from Lahijan to Gonbad-e Kavos. This fault, along with Khazar, Lalehband, Kandovan and Mosha faults affected by the shortening and rising of the Alborz Mountains. This shortening and uplift accompanied by large earthquake events that continue today. With knowledge of the geometry of faults and how faults are displaced and the use of computational methods for fault analysis and also, the Focal mechanism, direction of maximum tension governing the part of north Alborz fault has been determined. The two methods show acceptable results. In addition, the comparison of the findings with the results of geodetic studies of the scope, accuracy of the findings confirmed. The results of the study show that during the North Alborz Fault, the dominant vector is compressive, and the left-lateral slip is observed. From the central part of the Alborz to the east, the left lateral displacements increases and cause shear mechanism in the eastern parts of the Alborz. This movement has caused compressive earthquakes in the central Alborz and compressive-shear earthquakes in the eastern parts. Therefore, the magnitude of future earthquakes in the eastern part is slightly smaller than the central Alborz earthquakes.
خلاصه ماشینی:
با آگاهي از هندسه گسل ها و چگونگي جابجايي گسل ها و استفاده از روش هاي محاسباتي تحليل گسل ها و هم چنين با کمک حل سازوکار ژرفي گسلش ، جهت يابي ب يشي نه تنش حاکم بر بخشي از گسل شمال البرز که محدوده رخداد زمين لرزه بزرگ ١٣٣٦ سنگچال بوده ، تعيين شده است .
داده هاي گسلي در راستاي گسل شمال البرز، در پهنه رخداد زمين لرزه سنگچال برداشت شده است .
تحليل ويژگيهاي گسله هاي اين پهنه ، به منظور تعيين جهت بيشينه تنش حاکم ، راستاي شمال خاور- جنوب باختر را داده است .
تحليل داده هاي صفحه گسل ، راستاي بيشينه تنش (σ١) را در اين پهنه ، شمال باختر – جنوب خاور نشان داده است .
(به تصویر صفحه رجوع شود) شکل ٥: حل سازوکار ژرفي گسلش و جهت يابي تنش اقتباس شده از آن در زمين لرزه هاي بزرگ اطراف گسل شمال البرز.
(1990), Inversion of field data in fault tectonics to obtain the regional stress III: a new rapid direct inversion method by analytical means.
(1981), An inverse problem in micro- tectonics for the determination of stress tensors from fault striation analysis.
S. (1991), Brute3 and Select: Quick Basic 4 program for determination of stress tensor configurations and separation of heterogeneous populations of fault slip data.
J. (1995), A stress inversion procedure for more polyphase fault/slip data sets.
(1987), Determination of the tectonic stress tensor from slip along faults with Coulomb yield condition.
(2004), A stress inversion procedure for automatic recognition of polyphase fault/slip data sets.